Category: chlorides-buliding-blocks

Adding some certain compound to certain chemical reactions, such as: 6579-54-0, name is 2,6-Dichlorobenzenesulfonyl chloride, can increase the reaction rate and produce products with better performance than those obtained under traditional synthetic methods. Here is a downstream synthesis route of the compound 6579-54-0. 6579-54-0

General procedure: A mixture of N-Boc-aminol (1 eq.) and KOH (3eq) in THF was stirred vigorously for 15 min. It was followed by the addition of required benzenesulfonyl chloride derivative (1.2eq) and subsiquent stirring of the reaction for 4-5h. After completion of the reaction (as per TLC), the reaction mixture was filtered to expel out the precipitated salt and the filterate thus obtained was concentrated under reduced pressure to obtain the crude product which was further purified by column chromatography (eluent EtOAc:Hexane).

Chemical properties determine the actual use. Each compound has specific chemical properties and uses. We look forward to more synthetic routes in the future to expand reaction routes of 2,6-Dichlorobenzenesulfonyl chloride.

Reference:
Article; Saxena, Anil K.; Sharma, Sugandha; Pandey, Atindra K.; Shukla, Praveen K.; Bioorganic and Medicinal Chemistry Letters; vol. 21; 21; (2011); p. 6476 – 6481;,
Chloride – Wikipedia,
Chlorides – an overview | ScienceDirect Topics

Researchers who often do experiments know that organic synthesis is a process of preparing more complex target molecules from simple raw materials through one or more chemical reactions. Generally, it requires fewer steps, and cheap raw materials. 627-42-9, name is 2-Methoxyethyl chloride, A new synthetic method of this compound is introduced below., 627-42-9

General procedure: NaBH4 (23 mg, 0.60 mmol, 3.0 eq.) was portionwise added to a solution of 4,4′-diselanediyldibenzenesulfonamide 1 (94 mg, 0.20 mmol, 1.0 eq.) in EtOH (2 mL) at 0 C under inert atmosphere (N2). After 30 min, the halo-alkyl 2a-f (0.36 mmol, 2.1 eq.) was slowly added and the reaction mixture was stirred at reflux for 3 h, until complete consumption of the starting material was observed by TLC. The reaction was quenched by addition of saturated aq. NH4Cl (2 mL) and diluted with EtOAc (5 mL). The layers were separated and the aqueous layer was extracted with EtOAc (2 x 5 mL), dried over Na2SO4, filtered and concentrated under vacuum. The crude material was purified by flash chromatography to yield selenides (3a-f) bearing benzenesulfonamide moiety.

The basis of chemical reaction formula synthesis, the synthesis route is composed of some specific reactions and combined according to certain logical thinking. We look forward to the emergence of more reaction modes in the future.

Reference:
Article; Angeli, Andrea; di Cesare Mannelli, Lorenzo; Lucarini, Elena; Peat, Thomas S.; Ghelardini, Carla; Supuran, Claudiu T.; European Journal of Medicinal Chemistry; vol. 154; (2018); p. 210 – 219;,
Chloride – Wikipedia,
Chlorides – an overview | ScienceDirect Topics

5013-77-4, Each compound has different characteristics, and only by selecting the characteristics of the compound suitable for a specific situation can the compound be applied on a large scale. 5013-77-4, name is N-Methyl-2,4-dichlorobenzylamine, This compound has unique chemical properties. The synthetic route is as follows.

Into a 50-mL 3-necked round-bottom flask purged and maintained with an inert atmosphere of nitrogen, was placed a solution of 2-bromo 1 -phenyl ethanone (1 g, 5 05 mmol, 1 00 equiv) in 1,4-dioxane (20 mL) and (2,4-dichlorophenyl)-N-methylmethanamme (1 1 g, 5 82 mmol, 1 15 equiv) T?ethylamine (2 g, 19 80 mmol, 3 92 equiv) was added dropwise with stirring at 2O0C The resulting solution was stirred for 1 h at 2O0C in an oil bath The solids were filtered out The resulting mixture was concentrated under vacuum The residue was applied onto a silica gel column with ethyl acetate/petroleum ether (1 50) This resulted in 1 4 g (90%) of the title compound as a yellow oil.

If you are interested in these compounds, you can also browse my other articles.Thank you for taking the time to read this article. I hope you enjoyed it.

Reference:
Patent; ARDELYX, INC.; CHARMOT, Dominique; JACOBS, Jeffrey, W.; LEADBETTER, Michael, Robert; NAVRE, Marc; CARRERAS, Chris; BELL, Noah; WO2010/78449; (2010); A2;,
Chloride – Wikipedia,
Chlorides – an overview | ScienceDirect Topics

A common heterocyclic compound, 13078-79-0, name is 2-(3-Chlorophenyl)ethanamine, molecular formula is C8H10ClN, its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc, below Introduce a new synthetic route. 13078-79-0.

General procedure: To compound 5, 6 or 7 (1 equiv) and the appropriate alkylamine(1.3 equiv) in anhydrous DMF (10 mL/mmol) were added DIEA (3equiv) and PyBOP (1 equiv), and the reaction mixturewas stirred atroom temperature under argon. When the reaction was complete(2 h – 4 h), the solvents were removed under reduced pressure togive a residue that was taken up in CH2Cl2. The solution waswashed with saturated aqueous NaHCO3, then water. The organiclayer was dried over Na2SO4 and then evaporated in vacuo. Purificationby flash chromatography afforded the corresponding amidederivatives 8, 9 or 10 (yield: 40-76%).

The synthetic route of 2-(3-Chlorophenyl)ethanamine has been constantly updated, and we look forward to future research findings.

Reference:
Article; Paoletti, Julie; Assairi, Liliane; Gelin, Muriel; Huteau, Valerie; Nahori, Marie-Anne; Dussurget, Olivier; Labesse, Gilles; Pochet, Sylvie; European Journal of Medicinal Chemistry; vol. 124; (2016); p. 1041 – 1056;,
Chloride – Wikipedia,
Chlorides – an overview | ScienceDirect Topics

Each compound has different characteristics, and only by selecting the characteristics of the compound suitable for a specific situation can the compound be applied on a large scale. 112-26-5, name is 1,2-Bis(2-chloroethoxy)ethane, This compound has unique chemical properties. The synthetic route is as follows., 112-26-5

General procedure: A suspension of 4 (1.0g, 3.45mmol) and K2CO3 (0.47g, 3.45 mmol) in acetonitrile (20mL) was heated to 85oC. bis(2-chloroethyl) ether (0.49 g, 3.45 mmol) in acetonitrile (2.0 mL) was added dropwise over 3 h. The mixture was heated at 85oC for 36 h, cooled,and acetonitrile was removed in vacuum. The residue was acidified with dil. HCl (0.45M, 200 mL). The aqueous layer was extracted with chloroform (2¡Á20 mL). The chloroformlayer was dried over Na2SO4 and the solvent evaporated in vacuum to give an oily compound which was purified by column chromatography on silica gel using ethyl acetate: pet ether (2:8 v/v) (7)

If you are interested in these compounds, you can also browse my other articles.Thank you for taking the time to read this article. I hope you enjoyed it.

Reference:
Article; Utekar, Druman R.; Samant, Shriniwas D.; Journal of the Korean Chemical Society; vol. 58; 2; (2014); p. 193 – 197;,
Chloride – Wikipedia,
Chlorides – an overview | ScienceDirect Topics

81927-55-1,Some common heterocyclic compound, 81927-55-1, name is Benzyl 2,2,2-trichloroacetimidate, molecular formula is C9H8Cl3NO, traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc, below Introduce a new synthetic route.

To a solution of alcohol 5 (1.00 g, 8.61 mol) and benzyl 2,2,2-trichloroacetimidate26 (4.34 g, 17.2 mmol, 2.0 equiv) in 1,4-dioxane (15 mL) was added trifluoromethanesulfonic acid (0.15 mL, 1.72 mmol, 0.2 equiv) dropwise at room temperature under nitrogen. The reaction was stirred at room temperature for 1.5 h. The mixture was diluted with dichloromethane (35 mL), washed with saturated aqueous solution of sodium bicarbonate (25 mL*2) and brine (25 mL*3), dried over magnesium sulfate, filtered, and concentrated under reduced pressure. The residue was purified by flash column chromatography over silica gel (petroleum ether/ethyl acetate 5:1 to 2:1) to afford the titled compound as colorless oil (1.60 g, 90%). The 1H NMR spectrum was identical to literature data. 1H NMR (400 MHz, CDCl3) delta 7.30-7.19 (m, 5H), 4.62-4.54 (m, 1H), 4.56 (d, J=2.9 Hz, 2H), 3.59 and 3.49 (ABX, JAB=10.8 Hz, JAx=3.3 Hz, JBx=4.3 Hz, 2H), 2.59-2.34 (m, 2H), 2.26-2.13 (m, 1H), 2.09-1.97 (m, 1H).

These compound has a wide range of applications. It is believed that with the continuous development of the source of the synthetic route Benzyl 2,2,2-trichloroacetimidate, its application will become more common.

Reference:
Article; Yang, Fan; Feng, Liang; Wang, Nengzhong; Liu, Xuge; Li, Jun; Shen, Yuehai; Tetrahedron; vol. 69; 45; (2013); p. 9463 – 9468;,
Chloride – Wikipedia,
Chlorides – an overview | ScienceDirect Topics

432-21-3, In the chemical reaction process, reaction time, type of solvent, can easily affect the result of the reaction, thereby determining the yield and properties of the reaction product. An updated downstream synthesis route of 432-21-3 as follows.

1-Chloro-3-iodo-2-trifluoromethyl-benzeneTo a suspension of 3-Chloro-2-trifluoromethyl-phenylamine hydrochloride (30.9 g, iQ 0.16 mol) in H2O (90 mL) was added cone. HCI (65 mL) portion wise allowing the reaction to heat up to -45 0C. The temperature was maintained for 30 min then cooled in an ice bath < 5 0C. CH2CI2 (10 mL) was added and -10 min later a solution of sodium nitrite (13.6 g, 0.197 mol) in H2O (25 mL) was added dropwise. After a further 30 min, a solution of NaI (28.2 g, 0.188 mol) in H2O (50 mL) was again added dropwise keeping the temperature < 5 0C j 5 throughout both additions. After -1 h the reaction was diluted with CH2CI2 (200 mL) and sodium metabisulfite was added until the I2 color had been discharged. The layers were separated and the organic washed with brine, dried and the solvent evaporated to give 1- Chloro-3-iodo-2-trifluoromethyl-benzene (38.3 g, 79%) as an orange solid, which was used without further purification. MS: APCI: M+: 306.0 (305.9) At the same time, in my other blogs, there are other synthetic methods of this type of compound, 432-21-3, and friends who are interested can also refer to it. Reference:
Patent; PFIZER PRODUCTS INC.; WO2008/20306; (2008); A2;,
Chloride – Wikipedia,
Chlorides – an overview | ScienceDirect Topics

108-70-3, The chemical industry reduces the impact on the environment during synthesis 108-70-3, name is 1,3,5-Trichlorobenzene, I believe this compound will play a more active role in future production and life.

Example 97.2-(4,6-Dichloro- 1 -methyl- 1 H-indazol-3 -yl)-5H-pyrrolo [2,3 -b]pyrazine-7-carboxylic acid [(R)-2- (3-cyano-azetidin-l -yl)-l -methyl-2-oxo-ethyl]-amide 2,4,6-Trichlorobenzaldehyde was prepared according to the procedure outlined in Synthesis 2008, 279. To a solution of 1 ,3,5 -trichlorobenzene (10.0 g, 55.1 mmol) in THF (200 ml) at -78C was slowly added n-BuLi (1.6 M in hexanes, 34.4 ml, 55.1 mmol) over 20 min. The reaction mixture was stirred at -78C for 30 min then DMF (7.5 ml, 96.4 mmol) was added dropwise. The reaction was stirred at -78C for an additional 1.5 h then quenched with 3 N HC1 (200 ml) and warmed to room temperature. The mixture was extracted with EtOAc. The organic layer was washed with sat NaHCC”3 and brine then dried over MgSC^ and concentrated to afford 10.7 g (93%) of 2,4,6-trichlorobenzaldehyde as a white solid.

The chemical industry reduces the impact on the environment during synthesis 1,3,5-Trichlorobenzene. I believe this compound will play a more active role in future production and life.

Reference:
Patent; F. HOFFMANN-LA ROCHE AG; CHEN, Shaoqing; DE VICENTE FIDALGO, Javier; HAMILTON, Matthew Michael; HERMANN, Johannes Cornelius; KENNEDY-SMITH, Joshua; LI, Hongju; LOVEY, Allen John; LUCAS, Matthew C.; LUK, Kin-Chun Thomas; LYNCH, Stephen M.; O’YANG, Counde; PADILLA, Fernando; SCHOENFELD, Ryan Craig; SIDDURI, Achyutharao; SOTH, Michael; WANG, Ce; WOVKULICH, Peter Michael; ZHANG, Xiaohu; WO2013/30138; (2013); A1;,
Chloride – Wikipedia,
Chlorides – an overview | ScienceDirect Topics

363-51-9, Each compound has different characteristics, and only by selecting the characteristics of the compound suitable for a specific situation can the compound be applied on a large scale. 363-51-9, name is 2-Chloro-6-fluoroaniline, This compound has unique chemical properties. The synthetic route is as follows.

Step B: Preparation of l-chloro-3-fluoro-2-isothiocyanatobenzene A solution of 2-chloro-6-fluorobenzenamine (29.2 g, 0.20 mol) in chlorobenzene (200 mL) was treated with N,N-dimethylformamide (0.10 mL) and then thiophosgene (27.6 g, 0.24 mol) dropwise at room temperature. The reaction mixture was heated to reflux for 2.5 hours and allowed to stir at room temperature for 18 hours. The suspension was filtered through a pad of silica gel and washed with hexane. The filtrate was concentrated under vacuum to give a crude oil which was chromatographed on silica gel with hexane to yield the title compound as a light yellow oil (31.5 g). H NMR (CDC13) delta 7.23-7.19 (m, 1H), 7.18-7.13 (td, 1H), 7.10-7.04 (m, 1H).

If you are interested in these compounds, you can also browse my other articles.Thank you for taking the time to read this article. I hope you enjoyed it.

Reference:
Patent; E. I. DU PONT DE NEMOURS AND COMPANY; OBERHOLZER, Matthew, Richard; WO2014/189753; (2014); A1;,
Chloride – Wikipedia,
Chlorides – an overview | ScienceDirect Topics

Each compound has different characteristics, and only by selecting the characteristics of the compound suitable for a specific situation can the compound be applied on a large scale. 96558-78-0, name is 3-Bromo-5-chlorophenylamine, This compound has unique chemical properties. The synthetic route is as follows., 96558-78-0

To a solution of 3-bromo-5-chloro-aniline (0.2 g, 968.7 pmol, 1 eq), 2-isopropenyl- 4,4,5,5-tetramethyl-l,3,2-dioxaborolane (195.3 mg, 1.2 mmol, 1.2 eq) and K2CO3 (267.8 mg, 1.9 mmol, 2 eq) in 2 mL of dioxane and 0.2 mL of H2O was added Pd(dppf)Ch (70.9 mg, 96.9 pmol, 0.1 eq) and purged with N2 for 3 times. The mixture was stirred at 100C for 12 hours. The reaction mixture was partitioned between 3 mL of water and 5 mL of ethyl acetate. The organic phase was separated, washed twice with 2 mL of brine, dried over Na2SC>4, filtered and concentrated under reduced pressure to give a residue, which was purified by prep-TLC (S1O2, eluting with Petroleum ether : Ethyl acetate = 5: 1) to give 83 mg of compound 2 (495.1 pmol, 51.1 % yield) as a green oil

If you are interested in these compounds, you can also browse my other articles.Thank you for taking the time to read this article. I hope you enjoyed it.

Reference:
Patent; AQUINNAH PHARMACEUTICALS, INC.; VACCA, Joseph, P.; WAGER, Travis, T.; (383 pag.)WO2020/117877; (2020); A1;,
Chloride – Wikipedia,
Chlorides – an overview | ScienceDirect Topics